资料介绍
Table of Contents
AD7961 Native FMC Card & Xilinx Reference Design
Introduction
The AD7961 is an 16-bit, 5 MSPS charge redistribution successive approximation (SAR), analog-to-digital converter (ADC). The SAR architecture allows unmatched performance both in noise and in linearity. The AD7961 contains a low power, high speed, 16-bit sampling ADC, an internal conversion clock and an internal reference buffer. On the CNV± edge, the AD7961 samples the voltage difference between the IN+ and IN- pins. The voltages on these pins swing in opposite phase between 0 V and 4.096 V/5 V. The reference voltage is applied to the part externally. All conversion results are available on a single LVDS self-clocked or echo-clocked serial interface.
Supported Devices
Supported Carriers
Quick Start Guide
The reference design has been tested with KC705. It should be easily portable to other boards such as ML605 and VC707, only the UCF and MHS files need to be changed. The bit file provided combines the FPGA bit file and the SDK elf files. It may be used for a quick check on the system. All you need is the hardware and the programmer (IMPACT). This bit file configuration also captures 8192 samples from the ADC and saves them in a *.csv file.
Required Hardware
- KC705 board
- EVAL-AD7961FMCZ board
- Signal generator (for data)
Required Software
- Xilinx ISE (Programmer (IMPACT) is sufficient for the demo and is available on Webpack). Use the latest version or the one used in the reference design.
Running Demo (SDK) Program
If you are not familiar with KC705 and/or Xilix tools, please visit
products/boards-and-kits/EK-K7-KC705-G.htm for details.
Extract the project from the archive file to the location you desire.
Xilinx KC705 Setup
To begin, connect the EVAL-AD7961FMCZ board to the FMC-HPC or FMC-LPC connector (depending on archive file) of KC705 board (see images below). Connect power and USB cable from the PC to the JTAG USB connectors on the edge of the KC705. Connect a signal source to the AIN+(J5) and AIN-(J4) SMA connectors of the FMC card. After the hardware setup, turn the power on to the KC705.
FPGA Configuration
Start IMPACT, and initialze the JTAG chain. The program should recognize the FPGA device. Program the device using the ”../Bit/system.bit” file provided in the reference design archive..
Data Capture
At this point everything is set up and it is possible to start the evaluation of the ADI hardware. To capture data from the ADC run the data_capture.bat script located in the “../DataCapture” folder from the reference design .zip file. Every time the script is run a new batch of 8192 samples are read from the ADC at the ADC's maximum sampling rate and saved into the Acquisition.csv file located in the same folder as the data capture script. On the UART terminal messages will be displayed to show the status of the program running on the FPGA as shown in the picture below.
The first time the data capture script is run it is possible that an error will occur while the script is trying to connect to the system. Just run the script again and the error shouldn't appear anymore.
Using the reference design
Functional description
The reference design is built on a Microblaze based system. It consists of two functional modules, a LVDS interface, and a DMA interface. The LVDS interface captures and buffers data from the ADC. The data is captured using Echoed-Clock mode or Self-Clock mode (depending on the project). The DMA interface then transfers the samples to the external DDR-DRAM. The capture is initiated by the software, and transfered to the PC using a *.tcl script.
Downloads
FPGA Referece Designs:
- KC705 Echoed Clock: cf_ad7961_kc705_echo_edk_14_3_2013_07_17.zip FMC-HPC
- KC705 Self Clock Using Clock Generator: cf_ad7961_kc705_self_edk_14_3_2013_07_17.zip FMC-HPC
- KC705 Self Clock Using IDELAYE2: cf_ad7961_kc705_self_iodelay_edk_14_3_2013_07_17.zip FMC-LPC
- Questions? Ask Help & Support.
Zip file contents
The zip file contains, in most cases, the following files and/or directories. To rebuild the reference design simply double click the XMP file and run the tool. To build SDK, select a workspace and use the C file to build the elf file. Please refer to Xilinx EDK documentation for details.
More information
- AD7960和AD7961评估软件(zip,402 MB)
- AD7961 IBIS型号
- UG-581:评估AD7961 16位、5 MSPS脉冲星差分ADC
- FMC插入器&Xilinx KC705参考设计
- AD7656-1 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD7658-1 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- FMC-Imageon Xilinx ML605参考设计
- ADC-FMC插入器&Xilinx ZC706参考设计
- AD9833 FMC-SDP转接器和评估板/Xilinx KC705参考设计
- AD9671评估板、ADC-FMC转接器和Xilinx KC705参考设计
- AD9265本地FMC卡/ML605 Xilinx参考设计
- AD9434本地FMC卡和ML605 Xilinx参考设计
- AD7960 Wiki:FMC卡和Xilinx参考设计
- AD9467评估板、ADC-FMC插入器和Xilinx参考设计
- AD7961:16位、5 MSPS PulSAR差分ADC
- GD32 MCU 入门教程】GD32 MCU 常见外设介绍(12)FMC 模块介绍 632次阅读
- 【GD32F470紫藤派开发板使用手册】第四讲 FMC-片内Flash擦写读实验 903次阅读
- 如何本地部署大模型 2266次阅读
- Xilinx Zynq系统如何实现IEEE1588协议 3680次阅读
- HarmonyOS本地模拟器的版本演进与使用方法 6020次阅读
- Xilinx FPGA的FMC介绍 5643次阅读
- digilent FMC Pcam适配器介绍 2731次阅读
- 2.5 GSPS高性能数模转换器——AD9739A DAC 4675次阅读
- 关于FPGA的FMC接口的详细介绍 1.1w次阅读
- Xilinx Alveo U200数据中心加速器卡的主要性能和优势 6080次阅读
- Xilinx交叉编译链的安装步骤和验证 3113次阅读
- 基于Xilinx reVISION Stack Demo双摄像头采集图像 3309次阅读
- 基于FPGA 的FMC 接口应用实例 1w次阅读
- stm32案例分享之使D-CACHE时FMC外设运行不正常原因 1w次阅读
- FMC+标准将嵌入式设计推到全新的高度 1945次阅读
下载排行
本周
- 1HFSS电磁仿真设计应用详解PDF电子教程免费下载
- 24.30 MB | 128次下载 | 1 积分
- 2雷达的基本分类方法
- 1.25 MB | 4次下载 | 4 积分
- 3电感威廉希尔官方网站 讲解
- 827.73 KB | 2次下载 | 免费
- 4从 MSP430™ MCU 到 MSPM0 MCU 的迁移指南
- 1.17MB | 2次下载 | 免费
- 5有源低通滤波器设计应用说明
- 1.12MB | 2次下载 | 免费
- 6RA-Eco-RA2E1-48PIN-V1.0开发板资料
- 35.59 MB | 2次下载 | 免费
- 7面向热插拔应用的 I2C 解决方案
- 685.57KB | 1次下载 | 免费
- 8爱普生有源晶体振荡器SG3225EEN应用于储能NPC、新能源
- 317.46 KB | 1次下载 | 免费
本月
- 12024年工控与通信行业上游发展趋势和热点解读
- 2.61 MB | 763次下载 | 免费
- 2HFSS电磁仿真设计应用详解PDF电子教程免费下载
- 24.30 MB | 128次下载 | 1 积分
- 3继电保护原理
- 2.80 MB | 36次下载 | 免费
- 4正激、反激、推挽、全桥、半桥区别和特点
- 0.91 MB | 32次下载 | 1 积分
- 5labview实现DBC在界面加载配置
- 0.57 MB | 21次下载 | 5 积分
- 6在设计中使用MOSFET瞬态热阻抗曲线
- 1.57MB | 15次下载 | 免费
- 7GBT 4706.1-2024家用和类似用途电器的安全第1部分:通用要求
- 7.43 MB | 14次下载 | 免费
- 8AD18学习笔记
- 14.47 MB | 8次下载 | 2 积分
总榜
- 1matlab软件下载入口
- 未知 | 935113次下载 | 10 积分
- 2开源硬件-PMP21529.1-4 开关降压/升压双向直流/直流转换器 PCB layout 设计
- 1.48MB | 420061次下载 | 10 积分
- 3Altium DXP2002下载入口
- 未知 | 233084次下载 | 10 积分
- 4电路仿真软件multisim 10.0免费下载
- 340992 | 191360次下载 | 10 积分
- 5十天学会AVR单片机与C语言视频教程 下载
- 158M | 183329次下载 | 10 积分
- 6labview8.5下载
- 未知 | 81578次下载 | 10 积分
- 7Keil工具MDK-Arm免费下载
- 0.02 MB | 73804次下载 | 10 积分
- 8LabVIEW 8.6下载
- 未知 | 65985次下载 | 10 积分
评论
查看更多