完善资料让更多小伙伴认识你，还能领取20积分哦， 立即完善>
3天内不再提示
电子发烧友论坛|
嗨，我希望有人知道这里发生了什么
我有S2600CP主板，它可以很好地工作2x 2609 cpu但不适用于2x 2660v2 cpu 我已经将主板BIOS更新到最新版本的BIOS - 02.06.0006我仍然总是收到此错误 但如果我只使用其中一个，它也会工作，我也检查了led邮政编码意味着什么，并且简而言之 它点亮了数字7 6 5和3 2 1 我开始撕裂我的头发试图找出问题所在 我使用的ram是在4支装上以1333mhz非ecc进行的8演出，并且RAM可以正常使用2609 cpu 如果我遗失任何东西，我非常想听听它，或者你是否有一个神奇的解决方案 邮政编码.PNG 138.6 K. 以上来自于谷歌翻译 以下为原文 hi there i hope someone knows whats going on here i have the S2600CP motherboard where it works perfectly fine with 2x 2609 cpu´s but will not work with 2x 2660v2 cpu´s i have updated the motherboard bios to the latest version BIOS - 02.06.0006 i still always get this error but it will work if i just use one of them i have also check what the led post code means and that came up short it lights up led numbers 7 6 5 and 3 2 1 i am starting to tear my hair trying to figure out what the problem the ram im using is 8 gigs on 4 sticks at 1333mhz non ecc and the ram works just fine with the 2609 cpu´s if i am missing anything i would very much like to hear about it or if you have a magic solution for this
0
|
|
相关推荐
8个回答
|
|
|
您好Atil，感谢您加入社区。根据ark.intel.com，您正在使用的处理器型号受此板支持，因此不应该是问题。关于RAM配置您想要遵循上面描述的内存填充规则
本主板的威廉希尔官方网站 产品规格文件（第4.2.2.1节）。 第4.1节也支持处理器。请仔细看看这个，如果问题仍然存在，请告诉我们。希望这有助于.Jose A. 以上来自于谷歌翻译 以下为原文 Hello Atil, Thanks for joining the community. According to ark.intel.com both processor models that you are using are supported by this board, so that should not be the issue. About the RAM configuration you want to follow the memory population rules depicted on the Technical Product Specifications document (section 4.2.2.1) for this board. Also processor supported is in section 4.1. Please take a careful look at this and let us know if the issue persist. Hope this helps Jose A. |
|
|
|
|
jerry1978 发表于 2018-10-30 12:18 我已经通过手册，似乎没什么帮助 我试过把所有ram模块通道A和B放在什么都没做 在A频道放2支，在E频道放2个，我甚至没有试过在A1插槽中只用1根棍子但仍然没有 我甚至尝试填充A1插槽，C1插槽，E1插槽和G1插槽仍然没有变化 当我用一根ram做的时候我尝试了A1插槽我尝试了3种不同的ram仍然没有通过无效的dimm配置 以上来自于谷歌翻译 以下为原文 i have been trough the manual and it seems to be of little help i have tried putting all ram modules channels A and B that did nothing put 2 sticks in the A channel and 2 in the E channel still nothing i have even tried with just 1 stick in the A1 slot but still nothing i even tried populating the A1 slot, C1 slot, E1 slot and G1 slot still no change i did try the A1 slot when i did it with a single stick of ram i tried 3 different sticks of ram still it would not get past invalid dimm configuration |
|
|
|
|
cd340823 发表于 2018-10-30 12:27 您好Atli，当您收到错误消息时，是否有任何内存插槽LED指示灯亮起？您可以尝试以下最小配置：2 x 2660v2处理器，通道A1中的1个DIMM和E1Besides通道中的1个DIMM，您可以将部件号发送给我们 内存DIMM，所以我们可以确认它们是否被验证.Jose A. 以上来自于谷歌翻译 以下为原文 Hello Atli, Is there any memory slot LED illuminating when you get the error message? Could you try the following minimal configuration: 2 x 2660v2 processors, 1 DIMM in channel A1 and 1 DIMM in channel E1 Besides that could you please send us the part numbers of the memory DIMMs so we can confirm if they are validated Jose A. |
|
|
|
|
jerry1978 发表于 2018-10-30 12:38 我确实尝试了最小的配置，但仍然没有运气甚至尝试回到bios版本（02.03.003）我希望最新的BIOS有点错误，似乎不是这样的 至于ram stick我有以下几点： mushkin blackline 996677 x4（2gb stick） 海盗船cmv4gx3m1a1600c11 x1（4gb棒） hynix hmt325u6cfr8c - h9 x1（2gb棒） 我可以在双模式下运行2609或在单模式下运行2660v2时混合所有这些，但我主要使用糊状棒作为我的主要测试棒 当我收到此错误时，ram插槽旁边也没有指示灯 以上来自于谷歌翻译 以下为原文 i did try the minimal configuration and still no luck even tried going back a bios version (02.03.003) i was hoping the latest bios was somehow faulty that does not seem to be the case as for the ram sticks i have they are the following: mushkin blackline 996677 x4 (2gb stick) corsair cmv4gx3m1a1600c11 x1 (4gb stick) hynix hmt325u6cfr8c - h9 x1 (2gb stick) i can mix all of them when running the 2609 in dual mode or the 2660v2 in single mode but i have been mainly using the mushkin sticks as my primary test sticks also there are no lights next to the ram slots when i get this error |
|
|
|
|
fhdgxfvx 发表于 2018-10-30 12:58 你好Atli， 根据我们的serverconfigurator.intel.com> THOL构建器部分，从您使用的3个内存选项中，只有Hynix HMT325U7CFR8C-PB显示为已验证。 Mushkin受到支持，但您使用的特定型号未经过验证，海盗船也未经过验证。 我认为下一步将尝试使用2个Hynix模块并确认问题是否仍然存在。 希望这可以帮助 何塞A. 以上来自于谷歌翻译 以下为原文 Hello Atli, According to our serverconfigurator.intel.com> THOL builder section for this board, from the 3 memory options you are using only the Hynix HMT325U7CFR8C-PB shows up as validated. Mushkin is supported but the particular model you are using is not validated, neither is the corsair. I think the next step will be to try with 2 x Hynix modules and confirm if the issue persists. Hope this helps Jose A. |
|
|
|
|
jerry1978 发表于 2018-10-30 13:15 我要去看看我是否可以拿到一些经过验证的ram，因为我只有一根hynix ram，我会让你知道会发生什么 以上来自于谷歌翻译 以下为原文 i am going see if i can get my hands on some validated ram because i only have the one stick of hynix ram i will let let you know what happens |
|
|
|
|
|
我能够借用2支微米公羊模型MT18JSF1G72AZ-1G9E3ZF 它没有得到严格的批准，但它们的型号数量非常接近，但它们似乎确实做到了它同时启动的技巧2660v2 所以下一步将是在批准的列表上获得适当的内存 谢谢你的帮助，它帮助了很多 以上来自于谷歌翻译 以下为原文 i was able to borrow 2 sticks of micron ram model MT18JSF1G72AZ-1G9E3ZF it not strictly approved but they are very close in model number of those approved but they did seem to do the trick it booted right up with both 2660v2 so the next step will be to get proper memory thats on the approved list thank you for your help it helped alot |
|
|
|
|
jerry1978 发表于 2018-10-30 13:42 您好Atli，我很高兴听到您解决了问题。 这是一个真正的乐趣。我们将继续将此线程标记为已解决.RegardsJose。 以上来自于谷歌翻译 以下为原文 Hello Atli, I am glad to hear that you got it resolved. Its been a real pleasure. We will proceed to mark this thread as resolved. Regards Jose. |
|
|
|
|
只有小组成员才能发言，加入小组>>
561浏览 0评论
/6 
关注我们的微信
下载发烧友APP
电子发烧友观察
版权所有 © 湖南华秋数字科技有限公司
电子发烧友 （电路图） 湘公网安备 43011202000918 号 电信与信息服务业务经营许可证：合字B2-20210191
工商网监
湘ICP备2023018690号
4717
评论
淘帖
1910
